Drop in the drawing. We cut it in metal.

Steel, stainless and aluminium parts laser cut from your DXF. Drop the drawing here: it is read in your browser and measured the way we measure it before pricing.

Metal

Drop a DXF here

Times are for a 4 kW fibre laser. Sheets up to 3000 × 1500 mm.

Ask for a price

Priced from your drawing

The drawing goes with your request, so we price the part you drew, not a description of it. The price comes back by email, usually the same working day.

Ask for a price

A large laser cutting machine throwing sparks as it cuts a steel sheet on its bed
A sheet on the bed: the parts are cut, the skeleton stays.
A grey drawing of a plate with slanted slots, above the steel part cut from it
The drawing and the part cut from it: the outlines become the edges.

From the file to the part

  1. Drawn

    A DXF at full size in millimetres, one part to a file, every outline closed.

  2. Checked

    A person opens every drawing before it is priced and asks if something will not cut.

  3. Nested

    The parts are laid out on the sheet to waste as little metal as the shapes allow.

  4. Cut

    A fibre laser cuts each outline in one pass, starting from a pierce inside the waste.

  5. Finished

    Parts are knocked out of the skeleton, deburred where asked, bent or sent flat.

Three metals

Kept in stock in the thicknesses below, in sheets up to 3000 × 1500 mm.

MetalThickness, mmCut edge
Mild steel1 · 2 · 3 · 5 · 8 · 10Clean, with a thin dark oxide on the cut
Stainless steel1 · 2 · 3 · 5 · 8Bright, cut with nitrogen
Aluminium1 · 2 · 3 · 5 · 8Bright, a fine burr on the underside
Sparks under a laser head cutting stainless steel sheet
Stainless steel, cut with nitrogen so the edge stays bright.
The upper blade and lower die of a press brake, close up
A press brake: blade above, die below.
Garden grilles of laser-cut steel with coloured glass set into the openings
Patterns cut as easily as plain plates.

After the laser

  • BentOn a press brake, up to 3000 mm long. Mark the bends in the message or on their own layer.
  • DeburredEdges brushed smooth, so parts can be handled and painted.
  • FlatOr straight from the machine, packed flat and labelled with your drawing name.

Before you send a drawing

A laser cutting head close above a sheet on a bed of steel slats, sparks below
The cutting head, a few millimetres above the sheet.
Which files can I send?

DXF, saved at full size in millimetres. From a PDF or a sketch we can draw it for you first: ask in the message.

Why does it count pierces?

The laser burns through the sheet before every outline. Each pierce takes time, so many small holes cost more than one long cut.

How small can a hole be?

About as wide as the sheet is thick. Smaller holes are better drilled after cutting.

Can you bend the parts too?

Yes. Say where in the message, or send a drawing with the bend lines on their own layer.

Is the time on the page what I pay for?

It is the time under the laser, which is most of the cost. The price adds the metal, setting up and any finishing.

What happens to my drawing?

It is used to price and cut your parts and is kept with your request. We do not pass it on.

Drawing ready?

Pictures from Wikimedia Commons: Laserkop van Amada FO-4020NT 4kW, Contour, CC0; Laser cutting machine at PTM shop, Ptmtechnology, CC BY-SA 4.0; Laser cutting CAD and physical part, Mike1024, Public domain; Laserschmelzschneiden von Edelstahlblech, EGU-Metall, CC BY-SA 3.0; Mes en groef van een kantbank, Contour, CC0; Grilles en acier et verre découpés au laser, Roccella, CC BY-SA 4.0.